Getting Started with Plumbing Basics for Bathtub Installation
WebsiteThe publisher is making a number of great annotation regarding How to Install a Bathtub as a whole in this post down the page.
Setting up a bathtub isn't precisely rocket science, however it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging job. If the old bathtub is conveniently obtainable, the task can relocate quickly; if you have to open a wall surface to get rid of the old bathtub and position the new tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as embeded in the brand-new one. See to it you have qualified on your own for the job and also fit trying it. Instead of hiring a professional to take over a halfway-completed project, it is much better to consider utilizing one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This short article will certainly aid you set up a new bath tub in your restroom if you have currently purchased a brand-new tub and also do not need to alter the plan of your previous water system pipelines.
Your devices and material checklist need to make up the following:
Getting ready for the Installation
First of all, the sustaining structure supplied with the bath needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps unit to avoid pressure on the bathtub.
Fit the adaptable tap ports to the bottom of the two faucets using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the restricted accessibility that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to proceeding to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Tub
Making use of both wooden boards under its feet, position the bath tub in the required setting. The wood boards are practical in equally spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The next goal is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bath tub till the spirit level reads degree.
To mount taps, fit all-time low of the outermost versatile tap adapter to the appropriate supply pipe by making a compression join; then do the exact same for the various other tap.
Turn on the supply of water and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as additionally inspect the overflow outlet and also the regular electrical outlet for leaks.
Lastly, take care of the bath paneling as explained in the maker's user's manual. Tiling and also securing around the tub should wait till the bath tub has actually been made use of at least once as this will certainly settle it into its last position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washing machines are in area in between the faucet as well as the sink. Secure the faucet in position with the maker given backnut. When the tap is securely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former type should be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to split a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, resulting in problems with wetness as well as feasible leaks to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also installations. They are offered in tubes as well as cartridges, and can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to always load the bath tub with water before sealing, to permit the movement experienced when the bathtub is in use. The sealer can crack relatively early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently readily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on How to Install a Bathtub Yourself? Try to leave feedback further down. We will be delighted to hear your reactions about this piece. We are looking forward that you come back again before long. Appreciated our write up? Please share it. Help others check it out. Thank-you for taking the time to read it.
Schedule Your Job Now